SKF bearing ring die 2.5-3.2t/h wood sawdust pellet machine

SKF bearing ring die 2.5-3.2t/h wood sawdust pellet machine

Biomass energy profile
Biomass fuel is a renewable new energy. It has a huge economic and environmental benefits. Make full use of biomass energy can not only solve the problem of scarcity of resources today, but also to protect the Earth's environment. For the benefit of future generations, let us use biomass sources.

Raw materials of biomass fuel particles
Wood, logs, wood, waste wood, tree bark, straw, wheat straw, rice husk, cotton stalk, coconut juice slag, sunflower, olive pulp, paper, elephant grass, bamboo shavings, bagasse, palm shell, peanut shell, corn cob, soybean pole, weeds, branches, leaves, EFB, etc.

Application of biomass pellet
Biomass pellets are widely applied in industries like industrial boilers, home fireplace and biomass power generation and so on. Biomass pellet has gradually replaced industrialfuels like electricity, oil, gas and coal, and so on.

wood sawdust pellet machine

wood sawdust pellet line

(a) Peeling Process
Wood debarker machine is applicable to peel the log of MDF board and paper making industry, it is mainly used to peel log, small wood and so on, the peeled rate is more than 95 percent.

(b)Chipping Process
In the pellet plant before raw materials are made into biomass pellets, they are
first reduced into much smaller, uniformly-sized particles. When the thick is larger than 10mm or the size is greater than 50*50mm, a chipper is needed to chip these materials into smaller pieces.

(c)Grinding Process
The hammer mill is used to further crush these small pieces into particles of less than 3mm in diameter.

(d)Drying Process
After raw materials are crushed a dryer is needed since most raw wood materials have moisture content of about 50%. However, the optimal moisture content for pellet 13%-15%. Therefore a rotary dryer is included in the pellet plant to reduce the
moisture content. After crushing and drying you can begin making wood pellets.

(e)Pelleting Process
After crushing and drying the raw material properly it is then ready for the pellet mill.
The pelleting machine or press is the key piece of machinery in the pellet plant.
It should be mentioned that impurities in the raw materials like metal or stone,may
damage the die and rollers of pellet making machine.

(f)Cooling And Screening Process
Usually after pelleting, the temperature of pellets is between 60-80 degrees and the moisture content is close to 15%. For storage purpose, a cooler must be used to reduce their surface temperature and moisture content.

(g)Packing Process
Finally is the packing process. In order to protect the wood pellets becoming getting
damp and to increase stability, proper packing is necessary.

LD Company Profile

Business type: manufacturer, trading company
Location: ChangSkype： taishan0072, Jiangsu, China(mainland)
Year Established: 2003
Company certifications: ISO9001, CE, SGS
Main products:
We produce all of the machine in the biomass pellet process line such
as wood pellet mill,wood drum chipper,wood rotary drum dryer,wood
hammer mill,wood splitting machine,disc chipper,wood debarker,
wood cutting machine,wood briquetting machine.
We are professional in research and development of wood pellet machine line.
Jiangsu LD Machinery Co., Ltd. is a qualified manufacturer which specializes in developing,
producing and marketing top-class machinery equipment. Now we Skype： taishan0072 on pellet mill,hammer mill, mixer, drum dryer, wood chipper, packing machine, etc. and turn key projects.

The advantages of our quick installation, such as beautiful appearance, flexible operation,
stable performance and low operational cost are accepted by more and more customers.
We own an outstanding R&D team and a strict & scientific management system, which
enable us to supply high quality & convenient turn-key projects to all of our customers.

We have successfully produced over 1,000 turn key projects to clients, which make us
one of the biggest manufacturers and the most powerful factories for biomass machinery.
We have already sold our machines to over 80 countries, they are: Latvia, Russia, Slovenia,
France, Italy, Tunisia, New Zealand, Australia, Colombia, Brazil, Uruguay, Vietnam,
Thailand, Malaysia, Singapore, Indonesia, Algeria, the UAE, Kazakhstan, etc.
Some of our clients have become our indispensable agents and cooperate with us very well.

LD Certificate

LD Clients

LD Service

Pre-sale service:
Provide customers the parameters and confirm technical points
Share photos and videos With clients
Show our factory to clients for checking

On-purchase service:
Keep clients informed Of the production progress
Send photos to clients before shipment for checking
Arrange the visa for engineers who will go for guide assembly

After-sale service:
Training and all-around technical guidance for operation commission
and maintenance
Engineers abroad to for guide assembly
Detailed drawings from front view, vertical view ,side view.

If you are interested in the product page, to better understand and purchase, please fill out the form in Inquiry page to submit your contact information and product demand to us, we will contact you as soon as possible to resolve.
If you are interested in our products, please click "send" now! Please kindly tell us the following information:
1. What's the capacity you want?
2. What's the raw material?
3. What's the size of the raw material?
4. What's the moisture content?
5. What's the final pellet size do you want?
6. Automatic packing or manual packing needed?
7. What's your country voltage?

Packaging:Depending on customers' requirement,such as wooden box or Iron crate etc.
Shipping:Our shipping operator and Skype： taishan0072vering equipment will be ready on time to ensure goods shipped based on Sales Order requirement.

1.Q: How can I trust on your quality?
Answer:
1). All of the machine be tested successfully in LD workshop before shipment.
2). The working lifespan of LD machines is at least 20 working years.
3). LD wins 21 national patents for machines by our senior R&D engineers.

2. Q: What is your superiority comparing with other suppliers?
Answer:
1). LD can make optimal design based on your kinds of raw materials.
2). LD has overseas service center in USA, Germany, Italy, Malaysia, Tunisa etc, which can provide you spare parts very fast and on-site service quickly.
3). LD R&D ability is very strong, it can develop 8-10 new technology every year.
4). It has at least 90% traders and distributors place order for LD every year.

3. Q: Does your company provide Engineers Abroad Service?
Answer: Sure, we provide it. And we can provide free training for on-site workers.

4. Q: How to train our staff about operation and maintenance?
Answer : We will provide every detailed technical instructive, pictures, videos to teach them for the operation and maintenance. In addition, our engineers for guide assembly will teach your staff on site.

5. Q:What shipment terms you offer?
Answer: We can offer FOB, CIF, CFR etc based on your request.

6. Q:What payment terms you take?
Answer: T/T, LC at sight etc.

7. Where is your factory located? How can I visit there?
Answer: Our factory is located in Li yang City, Jiangsu Province, China, it is nearby Shanghai. You can fly to Shanghai airport or Nanjing Airport directly. We can ask our driver to pick you up at the airport or train station etc.

1